Using Arcserve UDP Agent (Linux) › How to Restore Volumes on a Target Node › Submit the Volume Restore Job

Submit the Volume Restore Job

Submit the volume restore job to start restoring your volume on the target node.

Follow these steps:

1. Log into the target node.
2. If the recovery points are in a local folder or shared network, submit the restore job using the following command:

   d2drestorevol --command=restore  --storage-path=<local_path> --node=<node_name> --rp=<recovery_point> --source-volume=<source_volume> --target-volume=<target_volume> [--encryption-password=<encryption_password>] [--mount-target=<mount_point> [--quick-recovery]]
   

   -command=restore

   Specifies that the volume restore job is submitted.

   --storage-path

   Specifies the path we determined in the Prerequisites topic. For more information, see Review the Prerequisites and Considerations.

   --node

   Specifies the source node that was backed up.

   --rp

   Specifies the recovery point or recovery session that you want to restore. Typically, a recovery point is in the following format: S00000000X, where X is a numeric value.

   --encryption-password

   Specifies the session password. This option is required if the session is encrypted. If the session is encrypted but this option is not present, you will be prompted to enter the password from the terminal.

   --source-volume

   Specifies the source volume. You can get the source volume using the command=info parameter as described in the Verify the Volume Details in the Session topic, or the source volume can be the it can be the mount point from the source system.

   --target-volume

   Specifies the device file path of the target node.

   Example: /dev/sda2

   --mount-target

   Specifies the mount point where the restored volume should be mounted.

   Example: /mnt/volrestore

   --quick-recovery

   When used along with ‘--mount-target’, the target volume will be mounted as soon as possible. You can use the data on the target volume while the data is getting restored.

   After the restore job is over, the restore process quits automatically and you can continue using the data without any interruption.

   Note: When a volume restore job, and a backup job run at the same time, then:

   • If --quick-recovery is used, then the job (volume restore or backup) that starts later does not run.
   • If --quick-recovery is not used, then the backup job will back up only those volumes that are not being restored.

   The restore job is submitted and a screen is opened that displays the progress. If you want to submit other jobs, you can either wait for the current job to complete or press Q to exit the screen and then submit a new job.

3. If the recovery points are in a RPS data store, submit the restore job using the following command:

   d2drestorevol --command=restore --storage-path=<rps_path> --node="<node_name>[UUID_number]" --rp=<recovery_point> --source-volume=/ --target-volume=<target_path_for_restore> --rps-host=<host_name> --rps-user=<user_name> --rps-pw=<rps_password> --rps-protocol=<internet_security_protocol> --rps-port=<port_number> --rps-dedup
   

   --command=restore

   Specifies that the volume restore ob is submitted.

   --storage-path

   Specifies the path we determined in the Prerequisites topic. For more information, see Review the Prerequisites and Considerations.

   --node

   Specifies the source node that was backed up in the following format:

   <node name>[<uuid>]

   --rp

   Specifies the recovery point or recovery session that you want to restore from a data store in RPS. Typically, a recovery point session from a RPS data store must be specified in the following format:

   VStore/S00000000X, where X is a numeric value

   --source-volume

   Specifies the source volume. You can get the source volume using the command=info parameter as described in the Verify the Volume Details in the Session topic, or the source volume can be the it can be the mount point from the source system.

   --target-volume

   Specifies the device file path of the target node.

   Example: /dev/sda2

   -- rps-host

   Specifies the host name of the RPS where the recovery session are stored.

   -- rps-user

   Specifies the user name to access the RPS host.

   -- rps-pw

   Specifies the password to access the RPS host.

   -- rps-protocol

   Specifies the protocol for the RPS host. The protocol is ether http or https.

   -- rps-port

   Specifies the port number of the RPS host.

   -- rps-dedup

   Specifies the data store has enabled deduplication. This parameter is required only when the the data store has enabled deduplication.

   -- ds-share-folder

   Specifies the shared path of the data store. This parameter is required only when the the data store has disabled deduplication.

   -- ds-user

   Specifies the user name for accessing the shared path of the data store.

   -- ds-user-pw

   Specifies the password for accessing the shared path of the data store.

   -- ds-pw

   Specifies the data encryption password if the data store also has enabled encryption.

   The restore job is submitted and a screen is opened that displays the progress. If you want to submit other jobs, you can either wait for the current job to complete or press Q to exit the screen and then submit a new job.

4. (Optional) Use the following command to review the progress of the volume restore job:

   d2drestorevol --command=monitor
   

   The progress details, such as volume name, elapsed time, progress, speed, status, and time remaining, are displayed on a screen.

   The screen exits when the job completes. You can also press Q to manually exit the screen. Manually exiting the screen does not interrupt the running restore job.

The volume restore job is submitted.